Your shopping cart is empty!
DRIVEN BY CARE
-
My Account Sign In / Register
×
Select Your Vehicle to Shop for the Correct Parts:
Show More Filters
1-36 of 236 results for Engine : Engine Hardware : All Productsgo
Sort by
Show
Show results for
Refine By
Availability
On Sale
Condition
Price
Under $10 (41)$10 to $25 (42)$25 to $50 (34)$50 to $100 (23)$100 to $250 (43)$250 to $500 (33)$500 & Above (20)
$ to $ go
Manufacturer
Show Less Filters
Model: 3149033
Condition: NEW
A handy tool to tighten the water pump pack nut. One word of caution--adjust it very carefully and only a little at a time, just enough to stop the leak. U.S.A.
…
Model: 3142667
Condition: NEW
Sets on top of the distributor body and the coil wire plugs into it. U.S.A.…
Model: 3138586
Condition: NEW
The authentic copper gaskets with a fiber core just like Ford used. Model A's and T's used this on the oil pan of the motor and Model T's used this same gasket for the oil plug on the rear end of 1909-25's. U.S.A.…
Model: 3174355
Condition: NEW
A 12" long piece of graphite impregnated ePTFF composite packing. Cut individual rings and stagger the joints. U.S.A.…
Model: 3197567
Condition: NEW
A set of 4 brass nuts used to mount the manifold. Brass won't corrode! U.S.A.…
Model: 3186659
Condition: NEW
For the show car, we have these copper gaskets with the filler gasket in them. U.S.A.…
Model: 3194422
Condition: NEW
For the 1932-34 B and C 4-cyl. motors. U.S.A.…
Model: 3191913
All piston sets are top quality, cam ground and made with modern materials. Wrist pins and retaining clips are included. This set includes one piston, wrist pin, and retaining clips. Order four if you are rebuilding your engine. We…
Model: 3191284
Condition: NEW
For adapting a modern compression tester to a stock Model A spark plug hole.
…
Model: 3171623
Condition: NEW
Product Overview Original flat strips, to connect the plugs to the distributor caps. 4 cylinder, 3-3/4" copper. …
Model: 3166593
Condition: NEW
These are the oil pan gaskets for the 1932-34 4-cyl engine.…
Model: 3162973
Condition: NEW
An excellent quality cam that has been carefully machined so timing is right on the money! B-profile and its American Made!!…
Model: 3155765
Condition: NEW
Set of 4 studs that screw into the block to mount the manifold. Our studs are American Made and are grade 8 material.…
Model: 3130103
Condition: NEW
For the 2-piece style shaft, this is the shaft that runs from the upper shaft to the oil pump drive gear. U.S.A.…
Model: 3128503
Condition: NEW
This holds the camshaft when adjusting the cam screw, and has a Z bend making it easier to use. There is no need to remove the distributor body from the engine when using this wrench.
…
Model: 3203086
Condition: NEW
The spring clips that hold the body onto the distributor housing. Set includes rivets. U.S.A.…
Model: 3199897
Condition: NEW
Extra heavy cup shaped washers that hold the intake and exhaust manifolds in place. The crown or high point of the washer goes away from the motor. U.S.A.…
Model: 3182172
Condition: NEW
Modern cap with plug wires and wire boots. Fits directly in place of the original distributor cap. This setup is beneficial if you are running a CB or radio in your Model A because it gets rid of the engine noise that is normally…
Model: 3179717
Condition: NEW
A nice cast steel pulley. The one piece pulley is what Ford put on the car when it left the factory. Machined to Ford specs.…
Model: 3171448
Condition: NEW
Tired of coolant weaping around the head! This unique gasket has a solid steel core sandwiched by heavy-duty high density gasket material coated with silicone. Additional high temperature silicone bands surround all water passages. Install…
Model: 3165406
Condition: NEW
For 4 cylinder, Model A & B
Oil Dip Stick - Original Cadmium-Plated Style - 4 Cylinder F,ord Model B
…
Model: 3162327
Condition: NEW
The cupped side of the washer faces the manifold.
…
Model: 3139404
Condition: NEW
Float valve (needle/seat) for the 1932-34 B Zenith carburetors. Viton tipped style needle which seals much better than the stock needle valve. U.S.A.…
Model: 3127427
Condition: NEW
Made from laminated shim stock. Two shims for rear main, and four for center and front main bearings. Fits 1932-34 "B" 4-cylinder motors. .016" thick, .002" per lamination. U.S.A.…
Model: 3018892
Condition: NEW
Best Quality Reproduction Chevy Engine Lift Brackets Stamped Steel Bare Metal Finish For Big Blocks 1965-1970 Your Early Chevy is too valuable for makeshift solutions. For your V8 conversion using quality stamped steel engine lift brackets…
Model: 3180508
Condition: NEW
Press into the distributor for the shaft to ride in. U.S.A.…
Model: 3166117
Condition: NEW
Reproduction Of Original
Used To Secure Washer Hoses, Under Dash, Power Antenna Wires, Etc...
…
Model: 3151091
Condition: NEW
Grease Fitting - Brass With Cap - Water Pump - Original - Fo,rd
…
Model: 3133870
Condition: NEW
This sleeve is pinned on the upper shaft at the base of the distributor to hold the shaft in place. Includes pin. U.S.A.…
Model: 3173362
Condition: NEW
If your carb has the later 1932 style carb, this is the gasket kit for that carb. U.S.A.…
Model: 3151674
Condition: NEW
Distributor body with brass inserts. U.S.A.
…
Model: 3150235
Condition: NEW
Quality Restoration Parts
Part Of A Popular Minor Modification
Will Fit And Function Like The Original Model A Clamp
Over the years many Model T owners saw the benefit of updating their cars with a Model A exhaust…
Model: 3125421
Condition: NEW
A set of 6 clamps with 4 for the lower hoses and 2 for the upper hose.
Now you can economically duplicate the flat style clamps used by Ford.
…